Rational design of a hydrophilic nanoarray-structured electro-Fenton membrane for antibiotics removal and fouling mitigation: An intensified catalysis process in an oxygen vacancy-mediated cathodic microreactor.

Electro-Fenton membranes (EFMs) can synchronously realize organic micropollutants destruction and fouling mitigation in a single filtration process with the assistance of hydroxyl radicals (•OH). Herein, a nanoarray-structured EFM (NS-EFM) was designed by assembling Fenton reactive CoFe-LDH nanowires using a low-temperature hydrothermal method. Combined with a defect-engineering strategy, the oxygen vacancies (OVac) in the CoFe-LDH nanoarrays were tailored by manipulating the stoichiometry of cations to optimize the Fenton reactivity of NS-EFMs. The optimized NS-EFM demonstrated exceptional sulfamethoxazole (SMX) removal (99.4%) and fast degradation kinetics (0.0846 min-1), but lower energy consumption (0.22 kWh m-3 per log removal of SMX). In-depth mechanism analysis revealed that the intrinsic electronic properties of OVac endowed NS-EFM with enhanced reactivity and charge transferability at metallic active sites of CoFe-LDH, thereby intensifying •OH generation. Besides, the nanoarray-structured NS-EFM built a confined microreactor space, leading to expedited •OH microflow to SMX. Meanwhile, the hydrophilic nature of CoFe-LDH nanoarrays synergistically contributed to the high flux recovery (95.0%) and minimal irreversible membrane fouling (5.0%), effectively alleviating membrane fouling within pores and on surfaces. This study offers insights into the potential of defect engineering as a foundational strategy in the design of EFMs, significantly advancing the treatment of organic pollutants and control of membrane fouling.

Effects of cations on biofilms in gravity-driven membrane system: Filtration performance and mechanism investigation.

The gravity-driven membrane (GDM) system is desirable for energy-efficient water treatment. However, little is known about the influence of cations on biofilm properties and GDM performance. In this study, typical cations (Ca2+ and Na+) were used to reveal the combined fouling behavior and mechanisms. Results showed that Ca2+ improved the stable flux and pollutant removal efficiency, while Na+ adversely affected the flux. Compared with GDM control, the concentration of pollutants was lower in Ca-GDM, as indicated by the low biomass, proteins, and polysaccharides. A heterogeneous and loose biofilm was observed in the Ca-GDM system, with roughness and porosity increasing by 43.06 % and 32.60 %, respectively. However, Na+ induced a homogeneous and dense biofilm, with porosity and roughness respectively reduced by 17.48 % and 22.04 %. The richness of bacterial communities increased in Ca-GDM systems, while it decreased in Na-GDM systems. High adenosine triphosphate (ATP) concentration in Ca-GDM system was consistent with the abundant bacteria and their high biological activity, which was helpful for the efficient removal of pollutants. The abundance of Apicomplexa, Platyhelminthes, Annelida and Nematoda increased after adding Ca2+, which was related to the formation of loose biofilms. Computational simulations indicated that the free volumes of the biofilms in Ca-GDM and Na-GDM were 13.7 and 13.2 nm3, respectively. The addition of cations changed intermolecular forces, Ca2+ induced bridging effects led to large and loose floc particles, while the significant dehydration of hydrated molecules in the Na-GDM caused obvious aggregation. Overall, microbiological characteristics and contaminant molecular interactions were the main reasons for differences in GDM systems.

Mechanistic insights into different illumination positions control algae production in anaerobic dynamic membrane filtration (AnDM) during decentralized wastewater treatment.

Sunlight illumination has the potential to control the stability and sustainability of dynamic membrane (DM) systems. In this study, an up-flow anaerobic sludge blanket (UASB) reactor was combined with DM under different illumination positions (direct, indirect and no illumination) to treat wastewater. Results indicated that the UASB achieved a COD removal up to 87.05 % with an average methane production of 0.28 L/d. Following treatment by the UASB, it was found that under illumination, the removal of organic substances by DM exhibited poor performance due to algal proliferation. However, the DM systems demonstrated efficient removal of ammonia nitrogen, ranging from 96.21 % to 97.67 % after stabilization. Total phosphorus removal was 45.72 %, and membrane flux remained stable when directly illuminated. Conversely, the DM system subjected to indirect illumination showed unstable membrane flux and severe fouling resistance. These findings offer valuable insights into optimizing illumination positions in DM systems under anaerobic conditions.

Emission characteristics of pulse CNT cold cathode X-ray source combined with channel electron multiplier.

Carbon nanotube (CNT)-based field emission X-ray source with the advantage of fast start-up response offers the chance to achieve high-frequency X-ray emission. In this study, a high-frequency random pulse X-ray source of CNT cold cathode combined with a channel electron multiplier (CEM) was built, and its direct current (DC) and pulse emission characteristics were tested. The DC measurement results were used for parameter selection for performing pulse experiments. During the DC test, with the conditions of 2.2 kV CEM bias voltage and 25 kV anode voltage, the anode currents are 141, 250, and 300 µA at grid voltages of 290, 387.6, and 432.2 V, respectively; the corresponding grid field values are 1.45, 1.94, and 2.16 V/µm. During the pulse test, the amplitude-frequency response of the X-ray source reaches 3.58 MHz at 3 dB. The developed pulse X-ray source was introduced into the X-ray communication (XCOM), and the experimental communication rate reached 6 Mbps with the bit-error-rate of 1.1 × 10-3. The developed high-frequency pulse CNT-CEM X-ray source has potential applications in XCOM, high-speed X-ray imaging, and other fields.

A preliminary study of multispectral Cherenkov imaging and a Fricke-xylenol orange gel film (MCIFF) for online, absolute dose measurement.

BACKGROUND: Cherenkov luminescence imaging has shown potential for relative dose distribution and field verification in radiation therapy. However, to date, limited research utilizing Cherenkov luminescence for absolute dose calibration has been conducted owing to uncertainties arising from camera positioning and tissue surface optical properties. PURPOSE: This paper introduces a novel approach to multispectral Cherenkov luminescence imaging combined with Fricke-xylenol orange gel (FXG) film, termed MCIFF, which can enable online full-field absolute dose measurement. By integrating these two approaches, MCIFF allows for calibration of the ratio between two spectral intensities with absorbed dose, thereby enabling absolute dose measurement. METHODS: All experiments are conducted on a Varian Clinac 23EX, utilizing an electron multiplying charge-coupled device (EMCCD) camera and a two-way image splitter for simultaneous capture of two-spectral Cherenkov imaging. In the first part of this study, the absorbance curves of the prepared FXG film, which receives different doses, are measured using a fluorescence spectrophotometer to verify the correlation between absorbance and dose. In the second part, the FXG film is positioned directly under the radiation beam to corroborate the dose measurement capacity of MCIFF across various beams. In the third part, the feasibility of MCIFF is tested in actual radiotherapy settings via a humanoid model, demonstrating its versatility with various radiotherapy materials. RESULTS: The results of this study indicate that the logarithmic ratios of spectral intensities at wavelengths of 550 ± 50 and 700 ± 100 nm accurately reflect variations in radiation dose (R2  > 0.96) across different radiation beams, particle energies, and dose rates. The slopes of the fitting lines remain consistent under varying beam conditions, with discrepancies of less than 8%. The optical profiles obtained using the MCIFF exhibit a satisfactory level of agreement with the measured results derived from the treatment planning system (TPS) and EBT3 films. Specifically, for photon beams, the lateral distances between the 80% and 20% isodose lines, referred to as the penumbra (P80-20) values, obtained through TPS, EBT3 films, and MCIFF, are determined as 0.537, 0.664, and 0.848 cm, respectively. Similarly, for electron beams, the P80-20 values obtained through TPS, EBT3 films, and MCIFF are found to be 0.432, 0.561, and 0.634 cm, respectively. Furthermore, imaging of the anthropomorphic phantom demonstrates the practical application of MCIFF in real radiotherapy environments. CONCLUSION: By combining an FXG film with Cherenkov luminescence imaging, MCIFF can calibrate Cherenkov luminescence to absorbed dose, filling the gap in online 2D absolute dose measurement methods in clinical practice, and providing a new direction for the clinical application of optical imaging to radiation therapy.

Theoretical and Experimental Aspects of Electrocatalysts for Oxygen Evolution Reaction.

Scientists are increasingly paying attention to using theoretical design as a guide combined with modern in-situ characterization techniques to develop catalysts with high activity, low cost, and long-term life. The review discusses the progress of catalyst theoretical design and corresponding experiments based on three typical oxygen evolution catalytic mechanisms, including the adsorbate evolution, lattice oxygen-mediated, and unconventional bifunctional mechanisms. This work briefly describes the commonly used tools and descriptors in theory as well as the electrochemical techniques and characterizations in experiments. Our purpose is to sort out the ways to closely integrate the theoretical method and experimental verification from the perspective of reaction mechanism, and to provide some experience reference for the future development of theoretical tools and experimental technologies.

Three-compartment membrane electrolyzer combining simultaneous desalination and oxidative degradation in treating nanofiltration concentrate.

The complex organic and inorganic solutes present in nanofiltration's purification by-product (NF concentrate, NFC) pose challenges to the water processing procedure. To address this, a three-compartment membrane electrolyzer was proposed that facilitates electro-driven ion migration for crystallization alongside synchronous anodic oxidation for organic degradation. With a hydraulic retention time (HRT) of 5 min and a current exceeding 50 mA, the system effectively separated over 25 % of inorganic salts and accomplished reclamation through crystallization in the concentration compartment. Simultaneously, it achieved oxidation of pollutants by more than 35 % based on the total nitrogen index and removed upwards of 15 % of organic carbon. Notably, the efficiency of pollutant removal correlated strongly with the intensity of the current. Furthermore, this study uncovered two issues encountered during the electrochemical process: membrane fouling and electrode fouling. During concentration, metal cations readily formed organic pollution by complexing with organic pollutants, while the crystallization of inorganics on the surface of anion exchange membranes emerged as a pivotal factor hindering current enhancement, similar to the formation of deposited salt in a solution. Long HRT can lead to electrode contamination and corrosion which subsequently affect current efficiency. Energy consumption verified the feasibility of the electrolyzer for NFC processing. Based on our findings, a current intensity of 100 mA (equivalent to a density of 8 mA/cm2) was deemed optimal, striking a balance between pollutant removal and various limiting factors associated with each pollutant. Consequently, this innovative advancement in membrane electrolyzers helps in overcoming limitations in synergistic desalination, ion recovery, and organic removal, establishing a fundamental component of the abbreviated flow process for future NFC treatment.

New progress in the deep understanding of the biocake layer property: Combined effect of neglected protein secondary structure, morphology, and mechanism.

The application of magnetic fields (MFs) and magnetic particles (MPs) in water treatment has attracted widespread attention due to their stability, strong biological compatibility, and less chemical consumption. This study introduced MPs and MFs to GDM and probed their effects on filtration performance. Predeposited large MPs (P-large) and batch-added little MPs (B-little) intervened biocake layer development, forming more open and porous structures, they also reduced biomass secretion, resulting in flux increases of 13 % in P-large and 40 % in B-little than P-little, respectively. Besides, MFs controlled MPs distribution on the biocake layer, resulting in forming of more rough and open structures. A relatively lower magnetic field of 20 mT facilitated biomass secretion, while a higher magnetic field of 50 mT decreased biomass. Furthermore, applying magnetic fields decreased the ratios of α-helix and ß-sheet, and increased random coil percentage. Thus, applying magnetic field mediation would contribute to the flux improvements in I-20 and I-50 by 29 % and 32 % relative to I-0. Economic analysis suggested introducing MPs and MFs to GDM was economically feasible, synergy of MPs and MFs had more economic advantages on the community scale and MPs-assisted GDM had significant economic advantages on both community and household scales. Future works should focus on developing new technologies for the recycling of MPs and membranes. This study provided new insight into the protein secondary structures associated with GDM performance and would encourage new sustainable MFs and MPs-assisted GDM technological developments.

Combined BNCT-CIRT treatment planning for glioblastoma using the effect-based optimization.

Objective. Boron neutron capture therapy (BNCT) and carbon ion radiotherapy (CIRT) are emerging treatment modalities for glioblastoma. In this study, we investigated the methodology and feasibility to combine BNCT and CIRT treatments. The combined treatment plan illustrated how the synergistic utilization of BNCT's biological targeting and CIRT's intensity modulation capabilities could lead to optimized treatment outcomes.Approach. The Monte Carlo toolkit, TOPAS, was employed to calculate the dose distribution for BNCT, while matRad was utilized for the optimization of CIRT. The biological effect-based approach, instead of the dose-based approach, was adopted to develop the combined BNCT-CIRT treatment plans for six patients diagnosed with glioblastoma, considering the different radiosensitivity and fraction. Five optional combined treatment plans with specific BNCT effect proportions for each patient were evaluated to identify the optimal treatment that minimizes damage on normal tissue.Main results. Individual BNCT exhibits a significant effect gradient along with the beam direction in the large tumor, while combined BNCT-CIRT treatments can achieve uniform effect delivery within the clinical target volume (CTV) through the effect filling with reversed gradient by the CIRT part. In addition, the increasing BNCT effect proportion in combined treatments can reduce damage in the normal brain tissue near the CTV. Besides, the combined treatments effectively minimize damage to the skin compared to individual BNCT treatments.Significance. The initial endeavor to combine BNCT and CIRT treatment plans is achieved by the effect-based optimization. The observed advantages of the combined treatment suggest its potential applicability for tumors characterized by pleomorphic, infiltrative, radioresistant and voluminous features.

Rapid azoospermia classification by stimulated Raman scattering and second harmonic generation microscopy.

Disease diagnosis and classification pose significant challenges due to the limited capabilities of traditional methods to obtain molecular information with spatial distribution. Optical imaging techniques, utilizing (auto)fluorescence and nonlinear optical signals, introduce new dimensions for biomarkers exploration that can improve diagnosis and classification. Nevertheless, these signals often cover only a limited number of species, impeding a comprehensive assessment of the tissue microenvironment, which is crucial for effective disease diagnosis and therapy. To address this challenge, we developed a multimodal platform, termed stimulated Raman scattering and second harmonic generation microscopy (SRASH), capable of simultaneously providing both chemical bonds and structural information of tissues. Applying SRASH imaging to azoospermia patient samples, we successfully identified lipids, protein, and collagen contrasts, unveiling molecular and structural signatures for non-obstructive azoospermia. This achievement is facilitated by LiteBlendNet-Dx (LBNet-Dx), our diagnostic algorithm, which achieved an outstanding 100% sample-level accuracy in classifying azoospermia, surpassing conventional imaging modalities. As a label-free technique, SRASH imaging eliminates the requirement for sample pre-treatment, demonstrating great potential for clinical translation and enabling molecular imaging-based diagnosis and therapy.

Spatial multiplexing for robust optical vortex transmission with optical nonlinearity.

Optical vortex beams, with phase singularity characterized by a topological charge (TC), introduces a new dimension for optical communication, quantum information, and optical light manipulation. However, the evaluation of TCs after beam propagation remains a substantial challenge, impeding practical applications. Here, we introduce vortices in lateral arrays (VOILA), a novel spatial multiplexing approach that enables simultaneous transmission of a lateral array of multiple vortices. Leveraging advanced learning techniques, VOILA effectively decodes TCs, even in the presence of strong optical nonlinearities simulated experimentally. Notably, our approach achieves substantial improvements in single-shot bandwidth, surpassing single-vortex scheme by several orders of magnitude. Furthermore, our system exhibits precise fractional TC recognition in both linear and nonlinear regimes, providing possibilities for high-bandwidth communication. The capabilities of VOILA promise transformative contributions to optical information processing and structured light research, with significant potential for advancements in diverse fields.

Photocatalytic membrane coated with α-Fe2O3/Fe3O4 for enhanced filtration performance and antifouling property in surface water treatment.

A photocatalytic membrane coated with α-Fe2O3/Fe3O4 nanoparticles has been developed to address the challenges of membrane fouling and organic removal in the treatment of natural surface water. The photocatalytic and filtration properties of the membranes were investigated through a variety of methods. The successful preparation of iron oxide was confirmed by UV-vis diffuse reflectance spectra and X-ray diffractometry, with α-Fe2O3 identified as the primary photocatalytic agent. A commercial ultrafiltration (UF) membrane was employed as a comparison to evaluate the photocatalytic performance and filtration properties of the modified membrane. Results showed that the photocatalytic membrane achieved better removal rates for UV254 (22.0%) and specific fluorescent organic compounds, such as component 2 (19.38%) and component 3 (16.89%), compared to the control group. Furthermore, both irreversible and reversible fouling resistances of the prepared membranes were significantly lower than that of the control group, with reductions of 39.4% and 50.2%, respectively. The membrane coated with α-Fe2O3/Fe3O4 nanoparticles exhibited moderate removal of protein-like and terrestrially derived humic-like fluorescent organics while controlling membrane fouling. Although the α-Fe2O3/Fe3O4 nanoparticles-coated photocatalytic membrane demonstrated good anti-fouling properties, the removals of organic matters were not as effective as anticipated due to the shorter hydraulic retention time. This study provides valuable insights for enhancing pollutant degradation and anti-fouling properties of membranes through the utilization of solar photocatalytic α-Fe2O3/Fe3O4 surface-modified membranes in the treatment of natural surface water.

Calculation of the DNA damage yield and relative biological effectiveness in boron neutron capture therapy via the Monte Carlo track structure simulation.

Objective.Boron neutron capture therapy (BNCT) is an advanced cellular-level hadron therapy that has exhibited remarkable therapeutic efficacy in the treatment of locally invasive malignancies. Despite its clinical success, the intricate nature of relative biological effectiveness (RBE) and mechanisms responsible for DNA damage remains elusive. This work aims to quantify the RBE of compound particles (i.e. alpha and lithium) in BNCT based on the calculation of DNA damage yields via the Monte Carlo track structure (MCTS) simulation.Approach. The TOPAS-nBio toolkit was employed to conduct MCTS simulations. The calculations encompassed four steps: determination of the angle and energy spectra on the nuclear membrane, quantification of the database containing DNA damage yields for ions with specific angle and energy, accumulation of the database and spectra to obtain the DNA damage yields of compound particles, and calculation of the RBE by comparison yields of double-strand break (DSB) with the reference gamma-ray. Furthermore, the impact of cell size and microscopic boron distribution was thoroughly discussed.Main results. The DSB yields induced by compound particles in three types of spherical cells (radius equal to 10, 8, and 6µm) were found to be 13.28, 17.34, 22.15 Gy Gbp-1for boronophenylalanine (BPA), and 1.07, 3.45, 8.32 Gy Gbp-1for sodium borocaptate (BSH). The corresponding DSB-based RBE values were determined to be 1.90, 2.48, 3.16 for BPA and 0.15, 0.49, 1.19 for BSH. The calculated DSB-based RBE showed agreement with experimentally values of compound biological effectiveness for melanoma and gliosarcoma. Besides, the DNA damage yield and DSB-based RBE value exhibited an increasing trend as the cell radius decreased. The impact of the boron concentration ratio on RBE diminished once the drug enrichment surpasses a certain threshold.Significance. This work is potential to provide valuable guidance for accurate biological-weighted dose evaluation in BNCT.

Gravity-driven membrane system treating heavy metals-containing secondary effluent: Improved removal of heavy metals and mechanism.

This study aimed at investigating the removal performance of the gravity-driven membrane (GDM) system in treating the heavy metals-containing secondary effluent, as well as evaluating the respective roles of Fe and Mn addition on the removal of heavy metals. GDM process with the formation of biocake layer exerted effective removals of Cr, Pb and Cd, with an average removal efficiency of 98%, 95% and 40%, respectively, however, after removing the biocake layer, the removal efficiencies of Cr, Pb and Cd reduced to 59%, 85% and 19%, respectively, indicating that the biocake layer played a fundamental role in removing heavy metals. With the assistance of Fe, the removal efficiency of heavy metals increased, and exhibited a positive response to the Fe dosage, due to the adsorption by the freshly generated iron oxides. On the contrary, the Mn involvement would result in the reduction of Cd removal due to the competitive adsorption of residual dissolved Mn2+ and Cd. Furthermore, the addition of a high dosage of Fe increased the diversity of eukaryotic communities and facilitated the elimination of heavy metals, however, the involvement of Mn would lead to a reduction in microbial diversity, resulting in a decrease of heavy metal removal efficiency. These findings are expected to develop new tactics to enhance heavy metal removal and promote widespread application of GDM technology in the fields of deep treatment of heavy metals-containing wastewater and reclamation of secondary effluent.

Effect of a Permanganate-Bearing Reactive Oxidant on Flocs in Electrocoagulation: Transformations and Interfacial Interactions.

The electrocoagulation/ultrafiltration (ECUF) process is expected to address the issues of current wastewater increments and complex water reuse. However, the underlying mechanism associated with flocs remains unclear in the ECUF system, especially in the upgraded permanganate-bearing ECUF (PECUF) system. Herein, flocs and their formation, response to organic matter (OM), and interfacial features in the PECUF process were systematically explored. Results demonstrated that permanganate contributed to the rapid start-up of the coagulation process by forming MnO2 and blocking the ligand-metal charge transfer process between adsorbed Fe(II) and solid-phase Fe(III). The response of flocs to natural OM (NOM) exhibited obvious time- and particle size-dependent characteristics. Based on this, the optimal NOM adsorption window was found to be in the interval of 5-20 min, whereas the optimal NOM removal window was located at the 20-30 min interval. Furthermore, the extended Derjaguin-Landau-Verwey-Overbeek theory revealed the underlying principle of the PECUF module for optimizing UF performance. On the one hand, it reduced the inherent resistance of the cake layer by modifying the colloidal solution, which guaranteed a small drop (15%) in initial flux. On the other hand, it enhanced the repulsive force among suspended particles to achieve a long-term antifouling effect. This study may provide insights into the selection and performance control of on-demand assembly modules in decentralized water treatment systems.

The Mechanisms of Inhibition Effects on Bubble Growth in He-Irradiated 316L Stainless Steel Fabricated by Selective Laser Melting.

The AISI 316L austenitic stainless steel fabricated by selective laser melting (SLM) is considered to have great prospects for applications in nuclear systems. This study investigated the He-irradiation response of SLM 316L, and several possible reasons for the improved He-irradiation resistance of SLM 316L were systematically revealed and evaluated by using TEM and related techniques. The results show that the effects of unique sub-grain boundaries have primary contributions to the decreased bubble diameter in SLM 316L compared to that in the conventional 316L counterpart, while the effects of oxide particles on bubble growth are not the dominant factor in this study. Moreover, the He densities inside the bubbles were carefully measured using electron energy loss spectroscopy (EELS). The mechanism of stress-dominated He densities in bubbles was validated, and the corresponding reasons for the decrease in bubble diameter were freshly proposed in SLM 316L. These insights help to shed light on the evolution of He bubbles and contribute to the ongoing development of the steels fabricated by SLM for advanced nuclear applications.

Frenkel Defect-modulated Anti-thermal Quenching Luminescence in Lanthanide-doped Sc2 (WO4 )3.

Although large amount of effort has been invested in combating thermal quenching that severely degrades the performance of luminescent materials particularly at high temperatures, not much affirmative progress has been realized. Herein, we demonstrate that the Frenkel defect formed via controlled annealing of Sc2 (WO4 )3 :Ln (Ln=Yb, Er, Eu, Tb, Sm), can work as energy reservoir and back-transfer the stored excitation energy to Ln3+ upon heating. Therefore, except routine anti-thermal quenching, thermally enhanced 415-fold downshifting and 405-fold upconversion luminescence are even obtained in Sc2 (WO4 )3 :Yb/Er, which has set a record of both the Yb3+ -Er3+ energy transfer efficiency (>85 %) and the working temperature at 500 and 1073 K, respectively. Moreover, this design strategy is extendable to other hosts possessing Frenkel defect, and modulation of which directly determines whether enhanced or decreased luminescence can be obtained. This discovery has paved new avenues to reliable generation of high-temperature luminescence.

Microdosimetric Analysis for Boron Neutron Capture Therapy via Monte Carlo Track Structure Simulation with Modified Lithium Cross-sections.

Boron neutron capture therapy (BNCT) is a cellular-level hadron therapy achieving therapeutic effects via the synergistic action of multiple particles, including Lithium, alpha, proton, and photon. However, evaluating the relative biological effectiveness (RBE) in BNCT remains challenging. In this research, we performed a microdosimetric calculation for BNCT using the Monte Carlo track structure (MCTS) simulation toolkit, TOPAS-nBio. This paper reports the first attempt to derive the ionization cross-sections of low-energy (>0.025 MeV/u) Lithium for MCTS simulation based on the effective charge cross-section scalation method and phenomenological double-parameter modification. The fitting parameters λ1=1.101,λ2=3.486 were determined to reproduce the range and stopping power data from the ICRU report 73. Besides, the lineal energy spectra of charged particles in BNCT were calculated, and the influence of sensitive volume (SV) size was discussed. Condensed history simulation obtained similar results with MCTS when using Micron-SV while overestimating the lineal energy when using Nano-SV. Furthermore, we found that the microscopic boron distribution can significantly affect the lineal energy for Lithium, while the effect for alpha is minimal. Similar results to the published data by PHITS simulation were observed for the compound particles and monoenergetic protons when using micron-SV. Spectra with nano-SV reflected that the different track densities and absorbed doses in the nucleus together result in the dramatic difference in the macroscopic biological response of BPA and BSH. This work and the developed methodology could impact the research fields in BNCT where understanding radiation effects is crucial, such as the treatment planning system, source evaluation, and new boron drug development.

A gravity-driven membrane bioreactor in treating the real decentralized domestic wastewater: Flux stability and membrane fouling.

Domestic wastewater in decentralized sites is capturing increasing attention. However, conventional treatment technology is not sufficiently cost-effective. In this study, real domestic wastewater was treated directly using a gravity-driven membrane bioreactor (GDMBR) at 45 mbar without backwashing or chemical cleaning, and the effects of different membrane pore sizes (0.22 µm, 0.45 µm, and 150 kDa) on flux development and contaminants removal were examined. The results showed that the flux initially decreased and then stabilized throughout long-term filtration and that the stabilized flux level of the GDMBR equipped the membranes with the pore size of 150 kDa and 0.22 µm was higher than that of 0.45 µm membrane and was in the range of 3-4 L m-2h-1. The flux stability was related to spongelike and permeable biofilm generation on the membrane surface in the GDMBR system. The presence of aeration shear on the membrane surface would cause the slough off of biofilm from the membrane surface, especially in the scenarios of GDMBR with the membrane pore size of 150 kDa and 0.22 µm, contributing to lower accumulation of extracellular polymeric substance (EPS) and smaller biofilm thickness compared to that of 0.45 µm membrane. Furthermore, the GDMBR system achieved efficient removals of chemical oxygen demand (COD), and ammonia, with average removal efficiencies of 60-80% and 70%. The high biological activity and microbial community diversity within the biofilm would improve its biodegradation and should be responsible for the efficient removal performance of contaminants. Interestingly, the membrane effluent could effectively retain total nitrogen (TN) and total phosphorus (TP). Therefore, it's feasible to adopt the GDMBR process to treat the actual domestic wastewater in the decentralized locations, and these findings could be expected to develop some simple and environmentally friendly strategies for decentralized wastewater treatment with fewer inputs.

The Relationship Between Psychological Flexibility and Depression, Anxiety and Stress: A Latent Profile Analysis.

Purpose: To explore the potential classification of psychological flexibility (PF) among Chinese college students, analyze whether there is group heterogeneity in PF, and discuss the differences in the latent profile of PF in the negative emotions of depression, anxiety, and stress. Methods: A total of 1769 college students were investigated using the Psychological Flexibility Questionnaire and Depression-Anxiety-Stress Self-rating Scale, and heterogeneity was tested by latent profile analysis. Results: The PF of college students can be divided into three latent profiles: self-contradiction group (19.2%), high PF group (34.1%), and low PF group (46.7%). The scores of depression, anxiety, and stress are significantly different among the groups. Conclusion: There is obvious group heterogeneity in the PF of college students, and they can be divided into the self-contradiction group, the high PF group, and the low PF group. The self-contradiction and low PF groups score significantly higher on the negative emotions of depression, anxiety, and stress than the high PF group.